inlet temperature

From experimental readings, the dynamic changing regularity of water wall parameters and the response curve are confirmed under the disturbance of outlet pressure, heat load, inlet mass flow speed and inlet temperature. Sone theoretical analyses are given.

在出口压力、热负荷、进口质量流速和进口温度参数扰动下，确定水冷壁参数动态变化规律和响应曲线，并进行了理论分析。

The entropy generation number N st of heat exchangers of several flowing pattern was compared with that of contraflow heat exchanger. The varying law of N st with the heat transfer unit number NTU, inlet temperature ratio τ and heat capacity ratio C was obtained.

将几种流动型式换热器相对于逆流式换热器进行了熵产生数相对值的比较，得到了熵产生数相对值随传热单元数、入口温度之比和热容量之比的变化规律。

The influence of inlet temperature of the cooling air and speed of glass ribbon ( tonnage) on flow rate and its tranverse distributions of the cooling air has been studied.

借助所建立的模型研究了冷却风量及其分布与冷却风进口温度、玻璃带运动速度（产量）之间的关系。

Under low flow condition, when the inlet temperature of storage tank is 11 degree, 12 degree, and 13 degree separately, the changing rule of the storage tank outlet water temperature and discharge velocity with time are compared.

在较小流量的条件下，比较了蓄冷槽进口温度分别为11℃，12℃，13℃时，蓄冷槽出口温度和取冷速率随时间变化的规律。

The weight can be reduced by raising inlet temperature properly;

适当地提高通风温度可以降低系统重量；

Moreover, static flow instability ( flow excursion) is also observed to occur for some conditions of low inlet temperature.

此外，在加热段入口温度较低时，亦可能在流量陡降区发生静态流动不稳定性（流量漂移）。

[ 3]. The paper also points out that the inlet temperature of the turbofan after& burner is low and the temperature exponent of the stability parameter may be smaller than 1.

本文还指出涡轮风扇加力室进口温度低，稳定准则中的温度指数可能小于1。

A Study on High Response Instrumentation Technology Used in Aero-engine Inlet Temperature Distortion Measurement

发动机进气温度畸变高响应温度测试技术研究

The main influencing factor was inlet temperature.

影响微球成型的主要因素为进风温度；

Gadget Jacket Charged by the Sun This paper introduces TMC ( thermal management controller), which can realize the functions of controlling inlet temperature of gas engine jacket water, polytype heating output and thermal management.

本文介绍了一种既可以控制燃气内燃机缸套水温，又可以实现多种类热用户热量输出和热能管理功能的热能管理器，并对其热能管理思路和设计过程进行详细阐述，给出了设计实例。

Stability Assessment Test Technology of a Turbofan Engine Inlet Temperature Distortion

某型涡扇发动机进口温度畸变的稳定性评定试验技术研究

The results show that the reaction profile of diesel fuel exhaust gas reforming was significantly influenced by the reformer inlet temperature with or without catalyst.

结果表明，无论有无催化剂，重整器入口温度是影响柴油重整反应的主要因素。

It is shown from the results that the inlet temperature rise just prior to system instability is approximately linear with the inlet temperature ramp rate.

数值结果表明，引起失速的进口温升近似地与进口温升率呈线性关系。

Inlet temperature distortion is one of the key factors effecting engine stability.

发动机进口温度畸变是影响发动机稳定性的关键因素之一。

Based on the study of how the inlet temperature and flow velocity of the secondary coolant and the thermoconductivity of the coil material affect the heat-conduction performance of the ice storage coil, we have designed and set up a new high-efficiency ice storage device.

研究了载冷剂进口温度、流速和盘管材料的热导率对蓄冰盘管传热性能的影响，并对完全冻结方式和不完全冻结方式的结冰和融冰过程作了比较。

In this article, the main influencing factors on condensation heat transfer include air flow rate, coolant flow rate, coolant inlet temperature and mixed gas velocity.

在本课题中，影响传热过程的因素主要有空气含量、冷却水流量、冷却水温度及混合气气速。

Fresh inlet temperature range which satisfies given error limits is achieved, and the effect of instrumentation precision on accuracy of test results is analyzed by calculating and analyzing uncertainties of sensible effectiveness tests.

通过对显热效率测试的不确定度的计算与分析，得出了满足给定误差限的新风进口温度范围，并分析了仪表精度对测试结果准确度的影响。

The world vertical upward flow round critical heat flux experimental database is analyzed based on the slice method, similarity measure, heat balance and inlet temperature verification.

采用切片法、相似度概念和热平衡以及进口温度检验法，对收集到的圆管垂直向上流动临界热流密度实验数据库进行了分析。

The performance of aero engine ( thrust-to-weight ratio, specific fuel consumption) can be improved by increasing the turbine inlet temperature and the compressor pressure ratio.

在提高压气机压比的同时，提升涡轮前温度是改善航空燃气涡轮发动机性能（推重比、耗油率）的有效措施。

Numerical simulation was carried ou for the manufactured cryoprobe. The results were compared with experiments. Good consistence was found between them on the effects of inlet temperature and pressure.

对所制作的低温探针进行了数值模拟，并和实验结果进行了比较，在进气压力和温度影响方面二者具有良好的一致性。

The model developed can be used to describe the change of methanol fractional conversion, space-time yield of hydrogen and the outlet temperature of bed at different operating conditions, such as raw material ratio, pressure, space velocity of liquid, wall temperature and inlet temperature.

考察了不同的原料液配比、系统压力、液空速、壁温及进口温度下甲醇的转化率、氢气的时空产率和床层出口温度的变化。

Design and Experimental Study of the Inlet Temperature Distortion Generator

温度畸变发生器的设计与实验

Based on the designed thin film evaporator, the influence of the rotor speed, feed rate and liquid inlet temperature on evaporation length and film heat transfer coefficient was primarily discussed using the software CFX 4.4 with water as feed liquid.

针对自行设计的薄膜蒸发器，以水为物料，采用大型CFD软件CFX4.4，初步探讨了刮板转速、进料量、进料温度等参量对薄膜蒸发器蒸发段长度和加热段膜内传热系数的影响。

Inlet temperature and velocity of hot air in heat channel, 650 K and 3 m/ s respectively.

加热空气进口温度650K、进口速度3m/s。

All models the same size, length, width and height of different sizes. Used for simulation analysis on the inlet temperature and entry speed to the cold, hot water temperature stratification and the thermal efficiency of the regenerative effect.

所有模型体积相同，长、宽、高的尺寸不同，用于模拟分析入口温度和入口速度对于冷、热水温度分层和蓄热效率的影响。